Nokea
A system undergoes an isobaric process (constant pressure). In this process, the work done (W) by the system is:
- A. Zero, if the volume change (ΔV) is zero.
- B. Positive and equal to the pressure multiplied by the volume change (W = PΔV).
- C. Negative and equal to the pressure multiplied by the volume change.
- D. Independent of the pressure or volume change.
Correct Answer: B
Rationale: In an isobaric process (constant pressure), the work done is given by the formula W = PΔV, where P is the pressure and ΔV is the change in volume. If the volume does not change, the work done is zero, not negative. Choice A is incorrect as it states the work done is zero when the volume change is zero, which is the correct condition for zero work. Choice C is incorrect as it incorrectly suggests that the work done is negative in an isobaric process. Choice D is incorrect as the work done in an isobaric process is indeed dependent on the volume change and pressure.
You may also like to solve these questions
Why doesn't a raindrop accelerate as it approaches the ground?
- A. Gravity pulls it down at a constant rate.
- B. Air resistance counteracts the gravitational force.
- C. Its mass decreases, decreasing its speed.
- D. Objects in motion decelerate over distance.
Correct Answer: B
Rationale: The correct answer is B. As a raindrop falls, it experiences air resistance which counteracts the gravitational force pulling it down. This balancing of forces prevents the raindrop from accelerating further as it approaches the ground. Choice A is incorrect because while gravity is pulling the raindrop down, air resistance opposes this force. Choice C is incorrect as the mass of the raindrop remains constant during its fall. Choice D is incorrect because objects in motion may decelerate due to various factors, but in this case, the focus is on why the raindrop doesn't accelerate.
Capillarity describes the tendency of fluids to rise or fall in narrow tubes. This phenomenon arises from the interplay of:
- A. Buoyancy and pressure differentials
- B. Density variations and compressibility of the fluid
- C. Viscous dissipation and inertial effects
- D. Surface tension at the liquid-gas interface and intermolecular forces
Correct Answer: D
Rationale: Capillarity occurs due to surface tension and intermolecular forces between the liquid and the walls of the narrow tube. These forces cause the liquid to rise or fall depending on the cohesion and adhesion properties. Surface tension at the liquid-gas interface and intermolecular forces are responsible for capillary action, making choice D the correct answer. Choices A, B, and C are incorrect as they do not directly relate to the specific forces involved in capillarity.
Which of the following is NOT a mode of heat transfer between a system and its surroundings?
- A. Conduction
- B. Convection
- C. Radiation
- D. Isothermalization
Correct Answer: A
Rationale: Isothermalization is not a mode of heat transfer. The three main modes of heat transfer are conduction (through direct contact), convection (through fluid motion), and radiation (through electromagnetic waves). In this question, choice A, conduction, is not a mode of heat transfer between a system and its surroundings. Conduction refers to heat transfer through direct contact between particles, without the movement of the particles themselves. Therefore, A is the correct answer. Choices B, C, and D are incorrect as they represent valid modes of heat transfer.
A 60-watt lightbulb is powered by a 110-volt power source. What is the current being drawn?
- A. 0.55 amperes
- B. 1.83 amperes
- C. 50 amperes
- D. 6,600 amperes
Correct Answer: A
Rationale: To calculate the current being drawn, use the formula I = P / V, where I is the current, P is the power in watts, and V is the voltage. Substituting the given values, I = 60 / 110 ≈ 0.55 amperes. Therefore, the current being drawn by the 60-watt lightbulb is approximately 0.55 amperes. Choice B, 1.83 amperes, is incorrect as it does not match the calculated value. Choices C and D, 50 amperes and 6,600 amperes, are significantly higher values and do not align with the expected current draw of a 60-watt lightbulb powered by a 110-volt source.
An object moves 100 m in 10 s. What is the velocity of the object over this time?
- A. 10 m/s
- B. 90 m/s
- C. 110 m/s
- D. 1,000 m/s
Correct Answer: A
Rationale: Velocity is calculated as the displacement divided by the time taken to cover that displacement. In this case, the object moves 100 meters in 10 seconds. Therefore, the velocity is 100 m / 10 s = 10 m/s. Choice B, 90 m/s, is incorrect as it doesn't match the calculated velocity. Choice C, 110 m/s, is incorrect as it is higher than the calculated velocity. Choice D, 1,000 m/s, is incorrect as it is significantly higher than the calculated velocity.