Nokea
When a dielectric material is inserted between the plates of a charged capacitor, what will happen to the capacitance?
- A. Increase
- B. Decrease
- C. Remain the same
- D. Become unpredictable
Correct Answer: A
Rationale: When a dielectric material is inserted between the plates of a charged capacitor, the capacitance will increase. This is because the presence of a dielectric material reduces the electric field between the plates, allowing more charge to be stored for a given voltage, thus increasing the capacitance. Choice B is incorrect because adding a dielectric material increases capacitance. Choice C is incorrect because capacitance changes when a dielectric is added. Choice D is incorrect because the effect of a dielectric on capacitance is predictable.
You may also like to solve these questions
A 25-cm spring stretches to 28 cm when a force of 12 N is applied. What would its length be if that force were doubled?
- A. 31 cm
- B. 40 cm
- C. 50 cm
- D. 56 cm
Correct Answer: A
Rationale: When the 12 N force stretches the spring from 25 cm to 28 cm, it causes a length increase of 28 cm - 25 cm = 3 cm. Therefore, each newton of applied force causes an extension of 3 cm / 12 N = 0.25 cm/N. If the force is doubled to 24 N, the spring would extend by 24 N 0.25 cm/N = 6 cm more than its original length of 25 cm. Thus, the new length of the spring would be 25 cm + 6 cm = 31 cm. Choice A, 31 cm, is the correct answer as calculated. Choices B, C, and D are incorrect as they do not consider the relationship between force and extension in the spring, leading to incorrect calculations of the new length.
In a circuit with three same-size resistors wired in series to a 9-V power supply, producing 1 amp of current, what is the resistance of each resistor?
- A. 9 ohms
- B. 6 ohms
- C. 3 ohms
- D. 1 ohm
Correct Answer: C
Rationale: In a series circuit, the total resistance is the sum of the individual resistances. With a total voltage of 9 V and a current of 1 A, we can use Ohm's Law (V = I R) to find the total resistance: Total resistance = 9 V / 1 A = 9 ohms. Since the resistors are identical and wired in series, the total resistance is evenly divided among the three resistors: Resistance of each resistor = 9 ohms / 3 = 3 ohms. Thus, the resistance of each resistor is 3 ohms. Therefore, the correct answer is 3 ohms. Choice A, 9 ohms, is incorrect because this would be the total resistance of all three resistors combined in series. Choice B, 6 ohms, is incorrect as it does not account for the equal distribution of resistance in a series circuit. Choice D, 1 ohm, is incorrect as it is too low for resistors in series with a total resistance of 9 ohms.
In a scenario where a transverse wave transports energy from north to south, in what direction do the particles in the medium move?
- A. Only north to south
- B. Both northward and southward
- C. Only east to west
- D. Both eastward and westward
Correct Answer: B
Rationale: In a transverse wave, particles of the medium move perpendicular to the direction of energy transport. When the wave transports energy from north to south, the particles in the medium oscillate up and down, causing them to move both northward and southward. Choice A is incorrect because the particles move in both directions, not only from north to south. Choices C and D are incorrect as they mention directions that are not relevant to the scenario described in the question.
What is the kinetic energy of a 500-kg wagon moving at 10 m/s?
- A. 50 J
- B. 250 J
- C. 2.5 10^4 J
- D. 5.0 10^5 J
Correct Answer: C
Rationale: The formula for calculating kinetic energy is KE = 0.5 mass velocity². Given the mass of the wagon is 500 kg and the velocity is 10 m/s, we can substitute these values into the formula: KE = 0.5 500 kg (10 m/s)² = 0.5 500 kg 100 m²/s² = 25,000 J or 2.5 10â´ J. Therefore, the kinetic energy of the 500-kg wagon moving at 10 m/s is 2.5 10â´ J. Choice A (50 J) is incorrect because it is too low; Choice B (250 J) is incorrect as it does not match the correct calculation; Choice D (5.0 10^5 J) is incorrect as it is too high. The correct answer is C (2.5 10^4 J).
Fluid dynamics is a subfield of fluid mechanics concerned with:
- A. Equilibrium properties of fluids at rest (Fluid Statics)
- B. The motion and behavior of fluids under various conditions
- C. Phase transitions of fluids between liquid, gas, and solid states
- D. Engineering applications of fluids (related but broader than fluid dynamics)
Correct Answer: B
Rationale: Fluid dynamics is the study of fluids in motion and their behavior under different conditions, including how they flow, mix, and interact with their surroundings. It focuses on the dynamic aspects of fluids rather than their static properties when at rest, which is the realm of fluid statics. Phase transitions of fluids between liquid, gas, and solid states are more related to thermodynamics than fluid dynamics. While engineering applications involve fluid dynamics, the field itself is more specialized in studying the movement and behavior of fluids.