Nokea
How do you determine the velocity of a wave?
- A. Multiply the frequency by the wavelength.
- B. Add the frequency and the wavelength.
- C. Subtract the wavelength from the frequency.
- D. Divide the wavelength by the frequency.
Correct Answer: A
Rationale: The velocity of a wave can be determined by multiplying the frequency of the wave by the wavelength. This relationship is given by the formula: velocity = frequency wavelength. By multiplying the frequency by the wavelength, you can calculate the speed at which the wave is traveling. This formula is derived from the basic wave equation v = f λ, where v represents velocity, f is frequency, and λ is wavelength. Therefore, to find the velocity of a wave, one must multiply its frequency by its wavelength. Choices B, C, and D are incorrect. Adding, subtracting, or dividing the frequency and wavelength does not yield the correct calculation for wave velocity. The correct formula for determining wave velocity is to multiply the frequency by the wavelength.
You may also like to solve these questions
A box is moved by a 15 N force over a distance of 3 m. What is the amount of work that has been done?
- A. 5 W
- B. 5 Nâ‹…m
- C. 45 W
- D. 45 Nâ‹…m
Correct Answer: D
Rationale: Work done is calculated using the formula: Work = Force x Distance. In this case, the force applied is 15 N and the distance covered is 3 m. Thus, work done = 15 N x 3 m = 45 Nâ‹…m. Therefore, the correct answer is 45 Nâ‹…m. Choice A (5 W) is incorrect because work is measured in joules (J) or newton-meters (Nâ‹…m), not in watts (W). Choice B (5 Nâ‹…m) is incorrect as it miscalculates the work by not multiplying the force by the distance. Choice C (45 W) is incorrect because work is not measured in watts (W) but in newton-meters (Nâ‹…m).
A 50-kg box of iron fishing weights is balanced at the edge of a table. Peter gives it a push, and it falls 2 meters to the floor. Which of the following statements is true?
- A. Once the box hits the floor, it loses both its kinetic and potential energy.
- B. The box had kinetic energy only when it was balanced at the edge of the table.
- C. The box had both kinetic and potential energy after it fell.
- D. Once the box hits the floor, it loses all its kinetic energy.
Correct Answer: C
Rationale: When the box is balanced at the edge of the table, it has potential energy due to its position above the ground. As Peter gives it a push, and it falls 2 meters to the floor, the box then has both kinetic energy (due to its motion) and potential energy (due to gravity). Therefore, the correct statement is that the box had both kinetic and potential energy after it fell. Option A is incorrect because the box retains its energy forms even after hitting the floor. Option B is incorrect as the box has kinetic energy both before and after falling. Option D is incorrect as the box still possesses kinetic energy even after hitting the floor.
For a compressible fluid subjected to rapid pressure changes, sound wave propagation becomes important. The speed of sound (c) depends on the fluid's:
- A. Density (Ï) only
- B. Viscosity (μ) only
- C. Density (Ï) and Bulk modulus
- D. Density (Ï) and Surface tension (γ)
Correct Answer: C
Rationale: In a compressible fluid, the speed of sound (c) depends on both the fluid's density (Ï) and Bulk modulus. Density affects the compressibility of the fluid, while Bulk modulus represents the fluid's resistance to compression and plays a crucial role in determining the speed of sound in a compressible medium. Viscosity and surface tension do not directly impact the speed of sound in a compressible fluid subjected to rapid pressure changes. Therefore, the correct answer is C.
During adiabatic compression of a gas, what happens to its temperature?
- A. Remains constant
- B. Decreases
- C. Increases
- D. Becomes unpredictable without additional information
Correct Answer: C
Rationale: During adiabatic compression, the gas's temperature increases. This is because no heat is exchanged with the surroundings, and all the work done on the gas results in an increase in internal energy. Choice A is incorrect because the temperature does not remain constant during adiabatic compression. Choice B is incorrect as the temperature does not decrease. Choice D is incorrect as the behavior of the gas's temperature during adiabatic compression is predictable based on the principles of thermodynamics.
In fluid machinery, pumps are designed to primarily increase the fluid's:
- A. Pressure
- B. Velocity only
- C. Both pressure and velocity
- D. Neither pressure nor velocity
Correct Answer: A
Rationale: Pumps in fluid machinery are designed to primarily increase the fluid's pressure. This increase in pressure allows the fluid to flow through the system efficiently and overcome resistance. While pumps can also impact the velocity of the fluid to some extent, their main function is to elevate the pressure to facilitate the movement of the fluid within the system. Choice B is incorrect because pumps do not focus solely on increasing velocity. Choice C is incorrect as while pumps can affect velocity, their primary purpose is to boost pressure. Choice D is incorrect as pumps aim to increase either the pressure, velocity, or both.